1xN MEMS 光开关产品图

1xN MEMS 光开关。

1xN MEMS 光开关

参考型号:FW-061-1XN-MEMS-OPTICAL-SWITCH-FW061(询价时请注明)

FW-061 系列 · 1xN MEMS 光开关中包含一个驱动板。

  • 1xN MEMS 光开关中包含一个驱动板
  • 该驱动板为 2D MEMS 芯片提供必要的驱动电路
  • 驱动板所需的电源为 5V/12V
  • 驱动板背面的 26 针连接器设计用于连接 Raspberry Pi,但也兼容任何 SPI 硬件

产品概述

1xN MEMS 光开关中包含一个驱动板。

该驱动板为 2D MEMS 芯片提供必要的驱动电路,使用户能够控制 0 至 60V 之间的四个模拟电压,从而驱动 MEMS 微镜。

驱动板所需的电源为 5V/12V,其内部的高压升压电路为高压数模转换器 (AD5504) 提供 60V 电源。

驱动板背面的 26 针连接器设计用于连接 Raspberry Pi,但也兼容任何 SPI 硬件。

规格参数

参数UnitM EMS 1×N -SM
工作波长nmO /C/L/ L + band
测试波长nm1310/1550/1625/1650
插损dB@CWL Single-band ≤0. 8 (N ≤ 8) ≤ 1.0 (8 ≤ 16) ≤1.3 (16 ≤1.5 (32 ≤2.0 (64 ≤2.2 (144@CWL Dual-band ≤1.0 (N≤8) ≤1.2 (8 ≤1.5 (16 ≤1.7 (32 ≤2.2 (64 ≤2.4 (144
WDLdB≤0.3 (N≤64) ≤0.4 (64 ≤0.5 (144
PDLdB≤0. 15
回损dB≥ 45
串扰dB≥ 50
可靠性dB≤ ± 0.05
切换时间ms≤ 15
耐久性times≥10 9
输出功率mW≤500
工作电压VDC 5V±10%
工作电流mA≤50 (N≤16) ≤250 (16 ≤350 (64 ≤500 (144
工作电压° C-20 ~ +85
储存温度° C-40 ~ +85
尺寸 (L ×W×H)mmM1: 34×24×11 ±0.2 (N≤64, Bare Fiber) M2: 60×24×11 ±0.2 (N≤16, Loose Tube) M3: 90×55×12 ±0.2 (16 M4: 100×100×12 ±0.2 (64 M5: 110×141×12 ±0.2 (144
1. 在工作温度和所有标准操作程序 (SOP) 范围内。 2. 不含连接器。 3. 工作距离 (WDL) 在 23°C 下测量,测量范围为 ±20nm。

选型与应用

产品类别:光开关。具体应用范围、安装条件与配套要求以本页产品概述及书面确认为准。

本页为 FW-061 系列离线预组装稿,尚未部署;参数保持源站技术规格,未为迁就图片改写。 因 fiberda 已有同名 slug,预发布路径使用 `1xn-mems-optical-switch-fw061`。

FW-061 产品说明

本产品为北亿纤通FW-061系列产品线,详细信息,请联系我们的销售人员,谢谢!

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. rther details are available from any F-tone Networks sales representative.

联系销售询价 联系我们

询价在线客服